NJ Transit GP40PH
The GP40PH is a diesel locomotive operated by NJ Transit.
Controls
Fuse panel
EngineStart
The engine start push button.
EngineStop
The emergency engine cutoff push button.
Control stand
VirtualBrake
The train brake control, also operated by the ;/' keys and the HUD. Ranges from 0 to 1.
| Value | Meaning |
|---|---|
| 0.0 | Release |
| 0.0 < x < 0.5 | Graduated Self Lap |
| 0.5 ≤ x < 1.0 | Full Service |
| 1.0 | Emergency |
VirtualEngineBrakeControl
The engine brake control, also operated by the [/] keys and the HUD. Ranges from 0 to 1.
VirtualSander
The sander push button, also operated by the X key and the HUD.
VirtualBell
The bell push button, also operated by the B key and the HUD.
VirtualHorn
The horn plunger, also operated by the Spacebar and the HUD.
VirtualWipers
The wiper switch, also operated by the V key and the HUD.
InstrumentLights
The gauge lights switch, also operated by the I key.
DitchLights
The ditch lights knob. 0 = off, 1 = flash, 2 = full.
ApplicationPipe
The suppression brake pressure gauge, in psi.
SuppressionPipe
The suppression brake reservoir gauge, in psi.
VirtualThrottle
The throttle control, also operated by the A/D keys and the HUD. Ranges from 0 to 1.
UserVirtualReverser
The reverser control, also operated by the W/S keys and the HUD. Ranges from -1 to 1.
StepsLight
The steps light switch.
NumberLights
The number lights switch.
Headlights
The headlights knob, also operated by the H/Shift+H keys and the HUD. Ranges from 0 to 2.
ADU
ACSES_Node
Illuminates the "SES" indicator light.
ATC_Node
Illuminates the "CSS" indicator light.
Speed2H
Sets the black hundreds digit on the speedometer display. -1 hides the digit.
Speed2T
Sets the black tens digit on the speedometer display. -1 hides the digit.
Speed2U
Sets the black ones digit on the speedometer display. -1 hides the digit.
SpeedH
Sets the green hundreds digit on the speedometer display. -1 hides the digit.
SpeedT
Sets the green tens digit on the speedometer display. -1 hides the digit.
SpeedU
Sets the green ones digit on the speedometer display. -1 hides the digit.
SpeedP
Moves the speedometer digits 0, 1, or 2 places over to compensate for a smaller number.
ACSES_SpeedGreen
Sets the green region of the circular speed limit bar. Ranges from 0 to 120 mph.
ACSES_SpeedRed
Sets the red region of the circular speed limit bar. Ranges from 0 to 120 mph.
AWSReset
The safety systems acknowledge button, also operated by the Q key and shown on the HUD.
Sounds
ACSES_Alert
Plays a continuous, rapid beep-beep sound.
ACSES_AlertIncrease
Plays a short upgrade tone.
ACSES_AlertDecrease
Plays a short downgrade tone.
AWSWarnCount
Plays an alarm whistle and illuminates the exclamation mark on the HUD.
Keyboard shortcuts
ATC
The Ctrl+F ATC on/off toggle. The default state is 0.
ACSES
The Ctrl+D ACSES on/off toggle. The default state is 0.
CabLight
The L cab dome light toggle. The default state is 0.
DoorsManual
The Ctrl+Shift+T manual doors on/off toggle. The default state is 0.
DoorsManualClose
The Ctrl+T manual doors close button. Value resets to 0 after one frame.
VirtualStartup
The Z engine start/stop toggle. The default state is 1 (run).
Destination
Cycles up/down with the Ctrl+Shift+5 and Ctrl+Shift+6 keys.
| Value | Destination |
|---|---|
| 1 | Trenton |
| 2 | New York |
| 3 | Long Branch |
| 4 | Hoboken |
| 5 | Dover |
| 6 | Bay Head |
Model nodes
ditch_front_left
ditch_front_right
ditch_rear_left
ditch_rear_right
The ditch light bulbs.
strobe_front_left
strobe_front_right
strobe_rear_left
strobe_rear_right
The strobe light bulbs.
lamp_on_left
lamp_on_right
The cab dome lamps (on the exterior model).
numbers_lit
The number board lights.
status_green
status_yellow
status_red
The brake indicator lights.
Lights
DitchFrontLeft
DitchFrontRight
DitchRearLeft
DitchRearRight
The ditch lights.
StrobeFrontLeft
StrobeFrontRight
StrobeRearLeft
StrobeRearRight
The strobe lights.
CabLight
The cab dome light.
Steplight_FL
Steplight_FR
Steplight_RL
Steplight_RR
The step lights.
Animations
Fans
Spins the exhaust fans.
Emitters
Exhaust
Exhaust2
Exhaust3
The exhaust emitters.
Consist messages
10100
Communicates the currently displayed destination sign to the passenger coaches. The argument is the ID of the destination.